Fly ash used as a reinforcing and flame-retardant filler in low-density polyethylene

A. Porąbka; K. Jurkowski; J. Laska

doi:10.14314/polimery.2015.251

Published : 2015-04-30

Vol. 60 No. 4 (2015)

Fly ash used as a reinforcing and flame-retardant filler in low-density polyethylene

A. Porąbka K. Jurkowski J. Laska

DOI: https://doi.org/10.14314/polimery.2015.251

Abstract

In this study, the possibility to modify low density polyethylene (PE-LD) with fly ash (FA) was tested. Four series of PE-LD composites filled with 1, 5, 20 or 50 wt % of FA were prepared by injection molding. The samples in each of the series differed in particle size of the filler used (0—15 µm, 15—30 µm, 30—60 µm). The influence of amount and the particles size of filler on morphology, mechanical properties, thermal stability and flammability of the composites were investigated. The results show that composites with the addition of FA in the amount up to 20 wt % are characterized by good mechanical properties and processability, and also smaller than the pure PE-LD, flammability.

Keywords

low-density polyethylene ; fly ash ; composites ; mechanical properties ; thermal properties ; flammability polietylen małej gęstości ; popioły lotne ; kompozyty ; właściwości mechaniczne ; właściwości termiczne ; palność

Details

References

Statistics

Authors

Download files

PDF

Zasady cytowania

Porąbka, A., Jurkowski, K., & Laska, J. (2015). Fly ash used as a reinforcing and flame-retardant filler in low-density polyethylene. Polimery, 60(4), 251-257. https://doi.org/10.14314/polimery.2015.251

References

Alam J., Akhtar M.N.: International Journal of Emerging Trends in Engineering and Development 2011, 1, 1.

[2] Garbacz A., Sokołowska J.J.: Construction and Building Materials 2013, 38, 689.
Crossref. 2012.08.052

[3] Vassilev S.V., Vassileva G.: Fuel 2007, 86, 1490.
Crossref

[4] Bose S., Mahanawar P.A.: Journal of Minerals and Materials Characterization and Engineering 2004, 3, 65.

[5] BN-79/6722-09 standard.

[6] Matsunaga T., Kim J.K., Hardcastle S., Rohatgi P.K.: Materials Science and Engineering 2002, 325, 333.
Crossref

[7]
Crossref (access date 6.12.2014).

[8] Ram A.: “Fundamentals of polymer engineering”, Plenum Press, New York 1997, p. 149.
Crossref

[9] Sperling L.H.: “Introduction to Physical Polymer Science”, Wiley, Hoboken 2006, pp. 737—739.
Crossref

[10] Biron M., Marichal O.: “Thermoplastics and thermoplastic composites”, Elsevier, Oxford 2013, pp. 136—139.

[11] Deepthi M.V., Sharma M., Sailaja R.R.N. et al.: Materials and Design 2010, 31, 2051.
Crossref

[12] Yao N., Zhang P., Song L. et al.: Applied Surface Science 2013, 279, 109.
Crossref

[13] Stark N.M., White R.H., Mueller S.A., Osswald T.A.: Polymer Degradation and Stability 2010, 95, 1903.
Crossref

[14] Obidiegwu M.U.: IOSR Journal of Engineering 2012, 2, 777.

[15] Onuoha F.N., Obasi H.C., Uzoma P.C., Ugbaja M.I.: The International Journal of Engineering and Science 2013, 2, 27.

[16] Madrzykowski D., Stroup D.W.: “Fire Protection Handbook”, National Fire Protection Assoc., Quincy 2008, vol. 1, p. 2/35.

Google Scholar

Altmetric indicators

Citing articles via

CITEDBY SCOPUS

Statistics

Total abstract views : 127

PDF Downloads : 89

A. Porąbka poranna@agh.edu.pl

Affiliation
AGH University of Science and Technology, Faculty of Materials Sciences and Ceramics, al. Mickiewicza 30, 30-059 Kraków, Poland

K. Jurkowski

Affiliation
AGH University of Science and Technology, Faculty of Materials Sciences and Ceramics, al. Mickiewicza 30, 30-059 Kraków, Poland

J. Laska

Affiliation
AGH University of Science and Technology, Faculty of Materials Sciences and Ceramics, al. Mickiewicza 30, 30-059 Kraków, Poland